Among consumers, awareness of the need for healthy living conditions has been increasing. Ecological aspects like the possible emissions from building products play a major role in meeting that demand. “Green living” as well as a variety of ecological seals for the classification of emissions have been in the focus of the media on a daily basis. Meanwhile, low-emission products are not just another trend – they represent a genuine shift in thinking and consumers start to consider the effects those materials have in their daily lives.
The PVAc dispersion adhesives of the Jowacoll® series are very low in formaldehyde and provide a solution for a wide range of applications due to their versatility.
Formaldehyde is a chemical that has been used for many years and which was originally used as a preservative to increase the shelf life of products. Due to technological processing reasons, several basic adhesive components like polyvinyl alcohol and vinyl acetate monomer already contain small amounts of formaldehyde. This is true for all adhesives based on polyvinyl acetate (PVAc). The formaldehyde con-tent is considerably higher in reactive D3 and D4 dispersions compared to classic PVAc dispersions. This is due to the crosslinking reaction of those PVAc dispersion adhesives which facilitates higher resistances. Formaldehyde is split off in a so-called condensation reaction.
Following extensive analyses, Jowat have succeeded in substantially reducing the formaldehyde content by optimize the manufacturing procedures. For instance, formaldehyde emissions of Jowacoll® 103.10 have been reduced by up to 80 % while the water and heat resistance of the product has not changed. Therefore, emissions of the reactive Jowacoll® D3 and D4 dispersions are below the permissible limits under different guidelines, and in some products even near the limit of detection.
The currently established method for determining VOC emissions from building products is described in the standards EN 16516 and ISO 16000 ff. The product is stored in a test chamber for a defined test duration of 28 days to get an indication of its emissions in the long term. Because that procedure is very expensive and time-consuming, the in-can method has become established for measuring the VOC emissions from the wet adhesive film. High Performance Liquid Chromatography (HPLC) facilitates a fast formaldehyde Analysis.
Formaldehyde is a colourless substance with a strong odour, which is gaseous at room temperature. In addition to its use and presence in different products, formaldehyde is also present in nature. Formaldehyde can be detected e.g. in the blood of mammals, in apples, grapes, and in wood. For instance, a kilogram (about two pounds) of apples has a formaldehyde content of up to 22 mg, and fresh fish up to 100 mg/kg. One kilogram of liquid Jowacoll® 103.10 has a formaldehyde content of approx. 49 mg.
If processed incorrectly, formaldehyde can cause allergies as well as irritation of the skin, eyes, and respiratory tract. High concentrations of formaldehyde are probably carcinogenic. For further information, please refer to our Safety Data Sheets. (upon request)
There are two types of emissions: from the liquid adhesive and from the cured adhesive film. Processors of the liquid adhesive are exposed to the former, and users of the end product are exposed to the latter.
The decisive limit values for the processor are the so-called Occupational Exposure Limits (OEL). These limits are measured directly at the workplace. Using appropriate measurement methods, it is, however, also possible to determine the total content of harmful ingredients like formaldehyde in the product itself.
There are a number of different classification methods available for evaluating the emissions from a finished part or from a product, i.e. the emissions from the cured glue film. The French VOC regulation with its rating from A+ (very low emissions) to C (highest permissible emissions level) is a very widely used classification system.
Currently established measurement procedures determine the total amount of emissions (TVOC) as well as the emissions of ten individual substances, including formaldehyde.
Since 01 January 2012, new building products, furnishing and decoration products introduced on the French market must be classified and labelled according to their emissions. The permissible limits are based on the total VOC emissions (TVOC) as well as on the evaluation of 10 individual substances, including formaldehyde (values in micrograms per m³). Jowacoll® 103.10 and 103.30 meet the requirements for a A+ classification.
|Base||Characteristics|| Viscosity [mPas] /|
|Solids [%]|| pH Value /|
| Components /|
| Classification |
acc. to EN 204
data sheet (PDF)
|Jowacoll® 103.10||PVAc Dispersion||General D3 glue with high heat resistance.||11000 ± 2000 / 20||50 ± 2 / 90||3,0 ± 0,5 / 20||195.40||D3 / D4||de en fr|
|Jowacoll® 103.30||PVAc Dispersion||PVAc dispersion adhesive with very high initial strength and heat resistance.||12500 ± 2500 / 20||52 ± 2||3,0 ± 0,5 / 20||195.40||D3 / D4 / WATT 91 > 7 N/mm²||de en fr|
Wymienione artykuły stanowią jedynie część dostępnego portfolio produktów. Dostępność produktów może się różnić w zależności od regionu. Dane techniczne, cechy i zakres zastosowania podane w tabeli przedstawiają różnice między poszczególnymi klejami z portfolio produktów. Nasz Dział Technologii nasi Przedstawiciele Handlowi służą radą oraz wsparciem w znalezieniu najlepszego kleju do konkretnego zastosowania.
Uwaga: Informacje na stronie oparte są na wynikach badań z naszych laboratoriów, a także na doświadczeniach zdobytych w tej dziedzinie i w żaden sposób nie stanowią gwarancji właściwości produktu. Ze względu na szeroką gamę zastosowań, podłoży i metod przetwarzania, na które nie mamy wpływu, nasza odpowiedzialność nie może wynikać z przedłożonych wskazań ani bezpłatnej usługi doradztwa technicznego. Próby przydatności u klienta w codziennych warunkach przechowywania oraz przetwarzania kleju oraz odpowiednie pomiary dla dopasowania najlepszego produktu są absolutnie konieczne. Dane techniczne oraz dodatkowe informacje znajdują się w najnowszych kartach technicznych.