Legal notice

1. Use of the website

1.1 Website content
The author does not assume any liability for the timeliness, accuracy, completeness or quality of the information provided. Liability claims against the author relating to material or non-material damage caused by the use or non-use of the information provided or by the use of incorrect or incomplete information are generally excluded, insofar as there is no demonstrable fault of an intentional or grossly negligent nature on the part of the author.

All content on this website is non-binding and is subject to change. The author expressly reserves the right to change, supplement or delete parts of the pages or the entire website without separate notice or to suspend publication temporarily or permanently.

Contact data published within the framework of the imprint or comparable details such as postal addresses, telephone and fax numbers as well as e-mail addresses may not be used by third parties for the purpose of sending information that has not been expressly requested. We expressly reserve the right to take legal action against the senders of so-called spam e-mails in the event of a violation of this interdiction.

1.2 References and links
In the case of direct or indirect references to external webpages ("hyperlinks") that lie outside the author's scope of responsibility, liability would only be assumed in those cases in which the author had knowledge of the content and where it would have been technically feasible and reasonable for him to prevent utilisation in the case of illegal content.

The author hereby expressly declares that at the time the links were posted, no illegal content was discernible on the pages linked to. The author has no influence on the current and future design, content or authorship of the pages linked to. For this reason, he hereby expressly distances himself from all content on all pages linked to that were changed after the link was posted. This disclaimer applies to all links and references posted on the author's own website as well as to external entries in guest books, discussion forums, link directories, mailing lists and all other forms of databases set up by the author and which can be filled with content by external write access. Liability for illegal, incorrect or incomplete content and in particular for damage arising from the use or non-use of such information lies solely with the provider of the page linked to, and not with the party who only refers to the respective publication via links.

1.3 Copyright and trademark law
The author endeavours to observe the copyrights for the graphics, sound documents, video sequences and texts used in all publications, to use graphics, sound documents, video sequences and texts created by themselves or to use licence-free graphics, sound documents, video sequences and texts.

All brand marks and trademarks mentioned on the website and possibly protected by third parties are subject without restriction to the provisions of the applicable trademark law and the ownership rights of the corresponding registered owners. The mere mentioning of a trademark does not imply that it is not protected by the rights of third parties.

The copyright for published objects created by the author himself remains solely with the author of the pages. Any duplication or use of such artworks, sound documents, video sequences or text in other electronic or printed publications is not permitted without the author's express consent.

1.4 Legal applicability of this disclaimer
This disclaimer is to be regarded as part of the website which linked to this page. If any part or individual provisions of this text do not, do not fully or no longer correspond to applicable law, the content and validity of the remaining portions of this document shall remain unaffected.

 

2. Notes on application responsibility and necessary suitability tests
Gluing as one of the most efficient methods of bonding is constantly gaining importance and expanding into new areas of application. At the same time, the number of substrates to be bonded is also growing at an unprecedented rate. New methods and equipment to process adhesives are developed.

The in-house R & D departments of Jowat are responding with intensive efforts to keep pace with these constant changes. A highly qualified team of chemists and engineers is using the latest techniques and brightest ideas to provide the utmost in advice our customers and to make sure that they get the adhesive which meets their needs.

Our information is based on test results from our laboratories as well as on experience gained in the field by our customers. This advice, however, cannot cover all eventualities for each specific application and as such is not binding for us. Please, contact our technical service department in each case to find out what the actual technical state of development for the respective product is, and request the latest data sheet. Any use of our product without this precautionary measure would be your sole responsibility.

The processing company itself must therefore test the adhesives manufactured by us for suitability in each individual case. This applies to the first use of a sample as well as to modifications during an ongoing production.

We are therefore requesting all our new customers to test our adhesives for suitability on original parts at conditions equal to normal processing conditions. The bond has then to be subjected to the actual stress which it would undergo when in use and has to be assessed. This test is absolutely necessary.

Customers who undertake modifications during a running production are requested to pass this information on to us. Please notify us when machines are set to new parameters as well as when the substrates to be bonded are changed. Only then will Jowat be able to provide our most up-to-date information to the processor using our adhesives.

The information given is based on practical experience and on results of tests in our laboratory, and does in no way constitute any guarantee of properties. No liability may be derived from these indications nor from the recommendations made by our technical advisory service.