Suche

vårt sökande efter "cycle" gav 14 resultat.

  1. Stringing-free bonding: clean and sustainable

    has to be tested to ensure that it meets the requirements, for example short cycle times, high restoring forces, demanding surfaces or special temperature resistance
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/stringing-free-bonding-clean-and-sustainable/

  2. Surfaces with a big impact - Lacquer glues in the last 25 years

    contents were then required that could safeguard the usually short process cycles in assembly operations in spite of the higher boiling point of water-based
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/surfaces-with-a-big-impact-lacquer-glues-in-the-last-25-years/

  3. Sticking PUR - mattress bonding with Jowatherm-Reaktant® 639.20

    minutes.” The use of PUR not only minimises storage periods and thereby increases cycle rates, it also only requires a significantly lower amount to achieve exceptional
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/sticking-pur-mattress-bonding-with-jowatherm-reaktantr-63920/

  4. Understanding – Bonding – Performing: Strong support for a smooth adhesive change

    requirements. This is followed by an extensive advisory on the entire process cycle of an adhesive change or introduction. For that purpose, more than 30 adhesive
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/understanding-bonding-performing-strong-support-for-a-smooth-adhesive-change/

  5. Polyurethane hot melt adhesives for mattress manufacture: Highest quality, maximum efficiency

    melt adhesives provide a solution for shorter and less complex production cycles. The individual mattress layers can be repositioned during assembly if necessary
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/polyurethane-hot-melt-adhesives-for-mattress-manufacture-highest-quality-maximum-efficiency/

  6. High-performance adhesives for the manufacture of filter media

    processing characteristics of the hot melt can be adapted easily to the process cycles and requirements in production. When the filter is assembled, the adhesive
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/high-performance-adhesives-for-the-manufacture-of-filter-media/

  7. PVC window profile wrapping: Jowat expands portfolio of adhesive systems

    procedure. The low processing temperature facilitates shorter production cycles, increases energy efficiency, and significantly reduces the risk of thermal
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/pvc-window-profile-wrapping-jowat-expands-portfolio-of-adhesive-systems/

  8. Print Finishing: the adhesive system for film lamination has to meet special requirements

    closing flaps will bond perfectly on the coated surface, even in short process cycles and with little pressure. Durable packaging that is resistant to mechanical
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/print-finishing-the-adhesive-system-for-film-lamination-has-to-meet-special-requirements/

  9. Protection against mineral oil migration: Barrier coating on cardboard packaging

    processing parameters of the used packaging technology with individual process cycles and individual time windows. Demanding development work in collaboration with
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/protection-against-mineral-oil-migration-barrier-coating-on-cardboard-packaging/

  10. Sustainably manufactured adhesives and efficient processing for box spring beds, foam mattresses and pocket innerspring mattresses

    facilitates faster process cycles. PO and PUR systems can handle high tensions and restoring forces even in short pressing cycles and are therefore ideal for [...] these products are assembled either totally or partially by hand, the process cycles vary very much and put high demands on the adhesive technology. In addition
    https://www.jowat.com/sv-SE/nyhetsrumdetalj/sustainably-manufactured-adhesives-and-efficient-processing-for-box-spring-beds-foam-mattresses-and/

Sortera efter

Ta bort alla filter